Maintenance on Jonway Chinese 50cc scooter

My scooter starts n revs up but wont move. What could be the cause of this?

jay wrote:

My scooter starts n revs up but wont move. What could be the cause of this?

It's a cheap piece of ChineseSHIT.

Order Scooter Parts wrote:

NEED HELP WITH YOUR JONWAY or CHINESE SCOOTER?
Here is a community forum to discuss this stuff, its a new forum so you might be the first to register and post but... I am the admin and I can help you!
http://www.orderscooterparts.com/scooter-foru...

Hi got a jonway aggressor 50cc dose it need 2 stroke oil and carn't find where engine oil can be chequed, hope you can help, thanks...

Just started my jonway agressor 50cc and oil light with buzzer wont stop, do i need to fill the clear tank near footwell with 2 stroke to stop this and where is the plug to cheque the engine oil...

The Jonway aggressor 50cc is a 2 stroke. There is no engine oil. The oil in the gas lubes the engine. You fill the oil tank with 2 stroke oil and the engine automatically mixes it with the gas.

ding70 wrote:

I have a Jonway 50cc 4 stroke gas scooter and you can turn it over, but it won't start. Are there any wiring schematics for the choke? or any of the electrical system? Please if anyone has any info it would be greatly appreciated.

I had the same problem was the petcock tri putting a shut off on your gas line

Had the same problem was the petcock try putting a shut off on the gas line

my mopad wont start,its like the bike nt gettin fire

my mopad wont start its like the spark plug nt gettin any fire

I have a 2 stroke 50cc Jonway, is there a way to make it go faster?

Jonway 150cc Adventure, three months old and won't go. Will start up but when I left off the gas it dies and it sounds very sluggish. Bad gas? Gummed ethanol from the gas? It has 325 miles on it. Put in a new battery today since I've not ridden it in a while and of course that didn't help.

DTx wrote:

Jonway 150cc Adventure, three months old and won't go. Will start up but when I left off the gas it dies and it sounds very sluggish. Bad gas? Gummed ethanol from the gas? It has 325 miles on it. Put in a new battery today since I've not ridden it in a while and of course that didn't help.

Fresh gas and put 2 oz. of Seafoam in the gas and see if that will clean it up.

I have a jonway hurricane and live in London..where on earth can I get it deristricted

Order Scooter Parts wrote:

I bought a jonway recently, Im very happy with it. I also started a website to sell scooter parts!
I can get any part for jonway and many other Chinese scooter including the GY6 engine and CN250 engine that Jonway uses. Its a honda engine without the honda stamp!
http://www.orderscooterparts.com

Do you have fuses?

Do you have a manual for Jonway? can you share a copy please?
Thank you sb

escholl wrote:

Does anyone know how to replace the gear oil on a Jonway Chinese-made 50cc scooter? I know how to replace the engine oil, but the owners manual also suggests replacing the gear oil after the first 300 km. It says "take off the gear oil filling bolt, fill in high quality gear oil, then fasten gear oil filling bolt". There are no illustrations in the manual and I can only find the engine oil drain bolt.

Mine is doing the same - changed the engine oil, spark plug, fuel, the fuel pump is pumping, the air filter is clear, the fuel filter is clean - I just give it a little throttle over idle and it dies. Did you get yours working?

Tami wrote:

<quoted text>
Make sure you have the proper air flow. This makes all the difference in the world!

please help me, i have jonway scooter 150cc that turned off on me as i was driving home.....it started to get slow and pull as if i was running out of gas eventhough the needle was not on empty i still stopped to pump more gas (filled up the tank) it started but in less than 5 min it started to pull again and stopped tried to restart it but i only get ignition noise and it sounds like it is starting but won't fully turn on...... what do i do???? somebody help me please.......

i have a 50cc 2 stroke wasp scooter anyone know the right spark plug gap should be set at. it says on the scooter to set it at .035 but it like runs like crap at that setting

The Jonway 50cc Wasp has a GY6 engine. Normal spark plug gap is .028-.030. The .035 seems way too big for a 50cc scooter. Gap it at .030 and see how it runs. Trial and error!

Were can i find a manual to download?